*Free Shipping With Every Order*

  • Home
  • STORE
  • PRODUCTS
    • HIP STICK
    • BOW HOLDER
    • GUN HOLDER
  • VIDEO
    • HIP STICK VIDEO
    • BOW/GUN HOLDER VIDEOS
  • INSTRUCTIONS
    • HIP STICK INSTRUCTIONS
    • BOW HOLDER INSTRUCTIONS
    • GUN HOLDER INSTRUCTIONS
  • More
    • Home
    • STORE
    • PRODUCTS
      • HIP STICK
      • BOW HOLDER
      • GUN HOLDER
    • VIDEO
      • HIP STICK VIDEO
      • BOW/GUN HOLDER VIDEOS
    • INSTRUCTIONS
      • HIP STICK INSTRUCTIONS
      • BOW HOLDER INSTRUCTIONS
      • GUN HOLDER INSTRUCTIONS
  • Sign In
  • Create Account

  • Orders
  • My Account
  • Signed in as:

  • filler@godaddy.com


  • Orders
  • My Account
  • Sign out


Signed in as:

filler@godaddy.com

  • Home
  • STORE
  • PRODUCTS
    • HIP STICK
    • BOW HOLDER
    • GUN HOLDER
  • VIDEO
    • HIP STICK VIDEO
    • BOW/GUN HOLDER VIDEOS
  • INSTRUCTIONS
    • HIP STICK INSTRUCTIONS
    • BOW HOLDER INSTRUCTIONS
    • GUN HOLDER INSTRUCTIONS

Account


  • Orders
  • My Account
  • Sign out


  • Sign In
  • Orders
  • My Account
Diagram of EBI's Bow Holder

EBI'S BOW HOLDER INSTRUCTIONS

 EBI’s Bow Holder/Accessory Hangers attaches to a variety Square Metal Tree Stands, Ground Blind Chairs, 2x4's... NO TOOLS REQUIRED. Strategically position the Base Station on the same side of the stand as which your hand grips the Bow’s handle. Simply slide the receiving end of the Base Station over the desired Square Flat Anchor Point. While being sure to allow the back / inside portion of the receiver remains square and firmly against the anchor point, tighten each of the two thumb screws clockwise until they are snug, then rotate between them back and fourth until tight. After the Base Station is secured in place, the Bow Holder’s Cushioned forks can be adjusted to allow your Bow to remain securely Up Right in a Ready To Grip and Draw Position. Simply loosen (do not remove) the thumb screw which

goes through the plate on the Bow Holder Forks to allow the positioning locking pin to be rotated and inserted into the proper half moon adjustment hole located on the front of the Base Station. (Make sure pin is seated in hole before tightening). Tighten the thumb screw until tight. The Bow Holder is now ready for your Bow / Crossbow. 


SECURING YOUR BOW/CROSSBOW: Slide the bottom limb of your bow/crossbow between the two cushioned forks and allow the top end of bow to lean forward. The weight of the top of the bow will create leverage. To release the bow from holder, grip the bow handle and move the bow slightly backwards releasing the pressure off the bottom limb. The Bow Holder has 2 accessory hangers to organize accessories within arms reach / out of harms way

IMPORTANT: Before each use, inspect Base Station and ensure proper

connection with its anchor point, if needed, tighten all thumb screws

EBI IS NOT RESPONSIBLE FOR THE USE OR MISUSE OF THIS PRODUCT

step-by-step DIRECTIONS ATTACHES WITH NO TOOLS IN UNDER 30 SECONDS

1. Loosen Bottom Thumb Screws to Accept Desired Flat Square Anchor Point

2. Hold Back of Base Station Flush Against Anchor Point. Tighten Bottom Thumb Screws until Snug then Alternate Between the Two Screws until Tight, Ensuring a Safe and Secure Connection 

3. To Adjust Bow Fork: Loosen Front Thumb Screw just enough to Allow Pin (Located on Back of Bracket) to Move Freely

4. Rotate Fork Lining up Pin with Desired Angle Positioning Hole (Make Sure Bow is in Proper Position) Tighten Thumb Screw

5. Hang Desired Accessories:

Range Finders, Binos, Calls,

Back packs etc. Off of Accessory Hangers

*IMPORTANT*

Keep All Bows and Crossbows Leaning Forward in Forks (DO NOT STAND BOW STRAIGHT UP AND DOWN) to Ensure Proper Pressure on Bottom Limb. Leverage pressure helps secure Bow/Crossbow Limb in Place)

SHOP NOW

BOW HOLDER VIDEO

BACK TO BOW HOLDER PAGE
  • Home
  • STORE
  • CONTACT US

EBI Inc

Copyright © 2023 EBI Inc ( Hip Stick) - All Rights Reserved.

ebiproducts@aol.com

FREE PRIORITY SHIPPING ON EVERY ORDER

SHOP NOW